(604) 767-3703

How to Install Blown-in Insulation For Your House

April 17, 2018

Filed under: Events — Richard Morrison @ 9:13 pm
I love my followers! Click LIKE or TWEET my post!

There are a lot of ways to insulate a house today, and one of the easiest ways to save on your energy costs is to add blown-in installation to your attic. The wonderful thing about this type of insulation is that absolutely anyone can do it themselves.

You don’t need a pro to help you, all you need is a free Saturday and you can add huge energy savings to your old house.


Types of Blown-in Insulation

There are two main options when it comes to blown-in insulation in most of the country.



Both options provide similar R-values but there are some notable differences that I think make the decision a no-brainer. I have used both and I greatly prefer using cellulose for a few reasons:

57% more fire-resistant than fiberglass

Uses 10 times less  energy to manufacture than fiberglass

Made from 85% recycled materials

Itch-free installation with no known adverse health effects

Better insulator against convective heat than fiber-glass

Those are some serious advantages in the favor of cellulose! When I insulated my house, I had no agenda other than to get the most bang for my buck in terms of insulating power and use the most eco-friendly product. Cellulose meets both of those requirements.

How Much Insulation Do I Need?

The easiest way to get started is in your attic. For most climates, adding a thick layer of insulation here will give you the greatest return on your investment.

How much insulation do you need? For most areas of the country, R-30 is the bare minimum, but you should definitely go higher than that, especially in colder climates.

Cellulose insulation is pretty affordable (around $12 per bag) and while you have the machine and you’re already getting messy, I would add as much insulation as possible.

How to Install Blown-in Insulation

Let’s start talking nuts and bolts here. You will need the following things to get the work done:

Cellulose (duh!)

Blowing machine

Safety glasses


Respirator or dust mask

Cellulose insulation isn’t a health hazard, but installing blown-in insulation does make a dusty mess and you want to protect your eyes and avoid breathing the dust filled air anymore than you need to.

You also don’t need to worry about wearing long sleeves since cellulose doesn’t make you itchy like fiberglass.

Setting up the Blower

I’m sure other hardware stores have similar deals, but I have to give Home Depot credit on this one. They will give you a free rental of an insulation blower if you purchase 20 bags or more of insulation. Not bad!

The blower comes with a long hose so you don’t have to haul it up the stairs if you don’t want to (which I don’t recommend because this thing is a heavy beast).

Setting up the blower is pretty straight forward. You just attach the hose, plug it in, and load some insulation into the hopper. You will need a helper to keep loading bags into the machine while you use the hose to direct the insulation where you want it.

Let it Blow

You’ll need to install the cellulose all across the attic floor starting from the furthest sections and working your way back to the exit. Blowing in insulation in this manner will give you what’s called “loose-fill” insulation.

The power of loose-fill is in its ability to slow down air and heat transfer through the thick fluffy blanket you blow in. This is different from “dense-pack” installation methods which are a little more complicated.

That being said, your goal here is to create the fluffiest covering of cellulose you can. Don’t blow it in and try to pack it down. It will settle a bit over time so always fill more than you think you should.

I would recommend a minimum of 10″ of loose fill for an attic floor, which should give you about an R-30 rating. But like I said earlier, if you’re gonna do it, you might as well do it right and add as much as you can.

I love my followers! Click LIKE or TWEET my post!

Leave a Reply